|
6/8/2009
jeremy (87%)
what type off speed controller should i uses on this. i used a super simple 60amp speed controller and after 1 min the speed controller blew up with a octura x440
|
|
|
 |
|
|
 |
|
5/23/2009
sietse (81%)
diameters are 28.1 and 34.4 mm.
Length is 57.9mm without axle and watertubes
|
|
|
|
|
|
|
|
|
5/23/2009
sietse (81%)
I have one, but it is purple instead of gold. Doesn't matter of course.
I've put it in a wave surfer with 35amp watercooled ESC and the standard prop. Bit smaller then the smallest prop here. On 2S lipo it runs good to very good. much faster then original and at the max of the boat.. On 3S it was only jumping out of the water with idle throttle
|
|
|
|
|
|
|
|
5/23/2009
Bjarne K (55%)
can anyone tell me how to take it apart
|
|
|
| |
|
Panpanta
(78%)
To remove the front black plate you have to unscrew it. The back where the water cooling is i can't remove it. I don't know if it is glued...
Can anyone tell us about ? how can i replase the inner bearing ? Thanks in advance.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Mel279 (73%)
Can this fit on a mount motor having 15mm Mounting Hole Distance ?
|
|
|
| |
|
Eric1180
(-55%)
probably not thats very small
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Marc (78%)
What timing setting should I use with the Turnigy 40 Amp ESC with this motor?
|
|
|
| |
|
sietse
(81%)
it's best to begin with low timing. Most inrunners run good at low timing. With a bit higher timing the motor will be faster, but will also draw more amps of course.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
spch1960 (84%)
What is the size of the motor?
|
|
|
|
|
|
|
|
|
Panpanta (78%)
I got one motor, when i am turning the shaft by hand, i feel it sticks for few degrees, like the magnet and rotor come in touch. Is that normal ? I haven't connect it to ESC yet. Could you please tell me if it is faulty or OK ? I have no experience of inrunners.
|
|
|
| |
|
Panpanta
(78%)
Please Admin or anyone else tell me something about...
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Panpanta
(78%)
Well... my motor was faulty...
Between the rotor shaft and the bearings the is shims, at my motor the shim was out of the shaft.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
alergigo (62%)
what are the sizes, please?are you going to have a marine esc?thanks
|
|
|
| |
|
alergigo
(62%)
20 junio 2008
thanks for the answer,
and the sizes, do you now it??
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Nikolaos (86%)
For TR 28-45 3600kv watercooled what mounting base i need ? Please provide product.Thanks
|
|
|
|
|
|
|
|
|
pylio (43%)
What is the size?
|
|
|
|
|
|
|
